有 278 筆資料符合您搜尋的條件
- 2017年 7月 26日, 18:18
- 版面: KUKA
- 主題: KR 3機器手臂主機板組裝作業/ Kuka KR3 for PC Board assembling applications
- 回覆: 10
- 觀看: 23435
KR 3機器手臂主機板組裝作業/ Kuka KR3 for PC Board assembling applications
系統架構:
A. KUKA KR3
B. KR C4 Compact Controller
C. 電腦主機板
D. 挾治具
程式開發: 卓智機器人
測試地點: 卓智機器人測試中心
挾治具設計與製作:精浚科技股份有限公司
應用:機器手臂執行電腦主機板組裝作業
- 2017年 7月 26日, 18:14
- 版面: KUKA
- 主題: KUKA 手沖咖啡/ KUKA Robotic pour-over coffee
- 回覆: 9
- 觀看: 18606
- 2017年 7月 26日, 18:14
- 版面: KUKA
- 主題: KUKA 手沖咖啡/ KUKA Robotic pour-over coffee
- 回覆: 9
- 觀看: 18606
- 2017年 7月 25日, 09:44
- 版面: KUKA
- 主題: 底座螺絲及其定位插銷問題
- 回覆: 2
- 觀看: 6444
- 2017年 7月 17日, 15:49
- 版面: KUKA
- 主題: 底座螺絲及其定位插銷問題
- 回覆: 2
- 觀看: 6444
Re: 底座螺絲及其定位插銷問題
機器手臂固定於鋼板上的螺絲尺寸會隨Robot的大小而不同,例如KR 6 Agilus使用4支M10,但KR 210 R2700則要求使用到8支M24,另外,底座鋼板固定於水泥地上所使用的螺栓,水泥鑽孔深度要求不同,以KR 6 Agilus 要求螺栓鑽孔深度必須大於110mm,而且水泥厚度必須大於190mm,然而KR 210 R2700則要求至少大於145mm以上,而且水泥厚度必須大於200mm以上。 參考資料如下: http://www.wtech.com.tw/public/download/manual/kuka/KUKA%20KR%206%2010_AGILUS.pdf http://w...
- 2017年 7月 17日, 14:34
- 版面: KUKA
- 主題: 底座螺絲及其定位插銷問題
- 回覆: 2
- 觀看: 6444
底座螺絲及其定位插銷問題
KUKA原廠手臂基本上不附底座、法蘭所需的固定螺絲及其定位插銷,因此必須依據原廠手冊(如下圖KR 6原廠手冊資料),準備所需螺絲及定位插銷! 以下圖片為KUKA KR 6手冊資料,底座使用M10螺絲4支,定位插銷2支(圓錐頭、Cylindrical stepped pin及導角 Flat-sided stepped pin),其中編號2為2階式定位銷,上下直徑不同,需特別注意! http://www.wtech.com.tw/forum/kuka/stepped_pin/KR%206%20%20Base%20B.png http://www.wtech.com.tw/forum/kuka/st...
- 2017年 5月 24日, 18:42
- 版面: KUKA
- 主題: KRC1 Software Limit Switch +A3
- 回覆: 8
- 觀看: 13183
Re: KRC1 Software Limit Switch +A3
I suggest you to contact your original dealer for the parts since they should have the robot parts documents, in which you can find the parts no. and make an order from your dealer.
- 2017年 5月 24日, 18:20
- 版面: Grass Hopper KUKA|prc
- 主題: RM501 MRC1 Controller Board.
- 回覆: 2
- 觀看: 10447
Re: RM501 MRC1 Controller Board.
you probably can find the solution on the following websites:
http://k8200-wiki.de/Controller
http://3dprintboard.com/showthread.php? ... 3D-printer
http://k8200-wiki.de/Controller
http://3dprintboard.com/showthread.php? ... 3D-printer
- 2017年 5月 1日, 10:46
- 版面: KUKA
- 主題: KUKA KR 3 直線運動精度量測
- 回覆: 2
- 觀看: 6443
Re: KUKA KR 3 直線運動精度量測
http://www.wtech.com.tw/forum/kuka/measuring_linear/kr%203%20line%20motion%2020170428C.png http://www.wtech.com.tw/forum/kuka/measuring_linear/kr%203%20line%20motion%2020170428A.png 排除各種可能的誤差問題後,這次量測的結果最為精準,誤差幾乎都在+- 0.05mm以內! 系統架構: A. KUKA KR3 B. KR C4 Compact Controller C. keyence IL1000 D.精密校正平台 ...
- 2017年 4月 5日, 18:59
- 版面: KUKA
- 主題: KUKA KR 3 直線運動精度量測
- 回覆: 2
- 觀看: 6443
Re: KUKA KR 3 直線運動精度量測
系統架構:
A. KUKA KR3
B. KR C4 Compact Controller
C. keyence IL1000
D.花崗岩精密平台
量測地點: 卓智機器人
運動模式: LINE Motion
量測誤差可能因素:1. 花崗岩或鐳射頭表面油漬 2. 花崗岩黑白紋路表面反射係數差異
應用:
機器手臂作業空間最佳化規劃設計